- V2.4
MGN12 X-axis
by arkeet
v1 · source 8e5067f · 15 files
Replaces the dual MGN9H rails with a single MGN12H.
2,543 views146 downloadsupdated
Images
Files
STL models (8)
STL models: Show or hide 8 files
- STLs/probe_retainer_bracket_9mm.stlSTL310 kBDownload
- STLs/x_carriage_frame_left.stlSTL681 kBDownload
- STLs/x_carriage_frame_right.stlSTL647 kBDownload
- STLs/x_carriage_frame_right_endstop.stlSTL768 kBDownload
- STLs/xy_joint_left_lower.stlSTL1.2 MBDownload
- STLs/xy_joint_left_upper.stlSTL982 kBDownload
- STLs/xy_joint_right_lower.stlSTL1.5 MBDownload
- STLs/xy_joint_right_upper.stlSTL736 kBDownload
CAD files (1)
CAD files: Show or hide 1 file
- CAD/V2.4_MGN12.stepSTEP36 MBDownload
Documents (1)
Documents: Show or hide 1 file
- README.mdMD2.5 kBDownload
README
MGN12 X axis
Note: Voron Trident officially uses a slightly improved version of this mod. It is suggested to use the X axis parts from Trident instead. https://github.com/VoronDesign/Voron-Trident/tree/main/STLs/Gantry/X_Axis
This replaces the dual MGN9H rails on the V2.4 X axis with a single MGN12H rail. The belt is directly clamped to the MGN12 block by the carriage.
The stock PL-08N probe might be too long to fit. Recommended alternatives are listed below.
As an option, the x_carriage_frame_right_endstop.stl allows mounting
the X endstop switch on the carriage, which is useful on an umbilical cable
setup.
Thanks to joshmurrah, hartk, and everyone else who helped out in one way or another.
Required hardware
In addition to things you can reuse from the stock build, these items are required:
- 1x MGN12 linear rail with MGN12H carriage (same length as the original MGN9 rails)
- 1x M3x40 SHCS
- 4x M3x8 BHCS (or 2x BHCS and 2x SHCS)
Recommended probes:
- Omron TL-Q5MC2 (use M3x25 or M3x30 screws)
- Panasonic GL-18HB/18HLB (use M3x25 or M3x30 screws)
- Panasonic GX-H15B/HL15B (use the 9mm probe bracket, and M3x16 or M3x20 screws)
Instructions
Assembly is similar to stock V2.4, see the assembly images below.
The belts are clamped between the carriage and the MGN12H block. This procedure worked for me:
- Loosely fasten the carriage to the MGN12H block using the M3x8 screws.
- Push the belts in on the left side, until they are just visible in the middle. Tighten the screws on the left side a little bit, to secure the belt ends.
- Push the belts in on the right side as far as you can, and pull them out through the middle.
- Tighten all screws, while making sure that all belts are firmly held in the clamp teeth.
- You may wrap the extra length of belt around the probe cable, as in the photo below.
Please check the Z endstop position after assembly as it may have changed slightly.
Images
Changelog
2021-07-26
- Fixed magnet position for Hall effect endstop. Both halves need to be reprinted.
2021-03-28
- Added option for mounting X endstop on the carriage.
- Updated readme to note that stock PL-08N probes might fit.
2021-03-21
- Initial release
Related mods
Dial test indicator mount
by arkeet
A toolhead mount for a dial test indicator, where the tip is located at the nozzle.- V1
- V2
300 views15 downloads
Magnetic hotend fan cover
by arkeet
A replacement hotend fan cover, held with magnets instead of screws.- V1
- V2
- VSW
287 views19 downloads
Angry CAM USB
by chri.kai.in
Housing for small USB camera module, allowing mounting to gantry or frame profiles- V2
14,187 views1,218 downloads
Belt Tension Meter
by Kruppes
Print in place tension meter to easily tighten multiple belts to the same tension- V0
- V1
- V2
- VSW
9,343 views1,131 downloads
Printable snap latches for 2020 extrusion
by richardjm
Quick release panel latch inspired by the work of others.- V2
12,147 views1,681 downloads