Belt Tension Meter
by Kruppes
Print in place tension meter to easily tighten multiple belts to the same tension
- V0
- V1
- V2
- VSW
9,343 views1,131 downloads
- V0.2
Raspberry Pi Camera Mount
by johanncc
v1 路 source 8e5067f 路 9 files
Low profile raspberry pi camera mount
1,504 views95 downloadsupdated
Images
Files
STL models (1)
STL models: Show or hide 1 file
- STL/Raspberry_Pi_Camera_Mount.stlSTL589 kBDownload
CAD files (1)
CAD files: Show or hide 1 file
- CAD/Raspberry_Pi_Camera_Mount.stepSTEP224 kBDownload
Documents (1)
Documents: Show or hide 1 file
- README.mdMD2.9 kBDownload
README
Voron 0/0.1 Raspberry Pi Camera Mount
This is a low profile raspberry pi camera mount for the Voron 0 / Voron 0.1.
Please consider downloading this model on Printables as well to help me earn a roll of Prusament 馃槅
TLDR
- Raspberry pi camera mount for the voron 0 / voron 0.1
- Get up close and personal with the nozzle & the print bed (>80% visible)
- Easy mounting with 1 M3x16 screw, 1 M3 nut and 1 M2x6 screws
- NO PRELOADING OF NUTS thank goodness!
- No supports as always!
- Battle tested by users on Thingiverse and Printables!
BOM
| Item | Qty. | Note |
|---|---|---|
| M2x6 BHCS/SHCS | 1 - 2 | For securing the Raspberry Pi Camera |
| M3x16 BHCS | 1 | For securing to profile |
| M3 Nut | 1 | For securing to profile |
| >300mm Flex Cable | 1 | May be optional, see notes |
Long Story
Ever since building my Voron 0.1, I've been trying to find a good mount for a raspberry pi camera. That said, most solutions I have found are a bit too conspicuous for my taste (i.e. they stick out into the tophat area), with no direct line of sight to the nozzle.
That's why I've decided to design my own and I've found a nice spot towards the top of the left z-extrusion with just enought clearance. It also offers good visibility of the nozzle & bed, extremely easy mounting, and great cable management!
Let me know what you think!
Notes
- The flex cable that comes with the camera module will be too short for this mod if your Raspberry Pi is located towards the bottom left of the electronics compartment (as per the manual). You can either purchase a 300mm / 12 in" flex cable or re-locate the Raspberry Pi towards the top of the compartment.
- Clearnace is quite tight (see one of the attached images), so I'd highly recommend that you check for inteference before commencing any prints. You can do so by moving the x-axis by hand along the back of the print bed. I'd also suggest that you check for any stray hotend wires so they don't snag on the camera
- Material choice is up to you, but if you're an enclosure (as I do), I'd highly recommend you print this model using ABS.
- The focus distance on the camera is usually set a too far out of the factory, resulting in a slightly blurry image. It is suggested that you adjust the focus ring on the camera to get a better image (not sure about warranty however).
Images
Raspberry pi camera model used in rendering designed by Peter H枚jerslev
Related mods
Extrusion/Chamber Thermistor Mount
by samwiseg0
Extrusion mount for a NTC100K Thermistor extrusion- V0
- V1
- V2
- VSW
- VT
4,605 views819 downloads
Cable Management Duct
by ryandam
Zip tie mount intergrated cable duct to hide your cable- V0
4,320 views804 downloads
Cricut Voron Logos
by GadgetAngel
For any cutting machines or machines that rely on vector graphics and use .svg files. These vectors or .svg files are the Voron Design Logos for the Voron 2.4, Voron SwitchWire, Voron 0.0/0.1. and Trident These .svg files use a minimal amount of anchor points to achieve the vector shapes!- V0
- V2
- VSW
- VT
3,969 views683 downloads
HorseshoeSpoolHolder
by LoganFraser
Horseshoe Spool Holder - mounts internally for Trident, or externally for V0, V1, or V2 printers.- V0
- V1
- V2
- VT
4,171 views258 downloads